General Pump O-Ring 1.239" ID Buna-N 70 Duro - 5140

In Stock Quantity Available: 29

Specifications

SKU: 5140

INTERNAL DIAMETER

1.239"

MFG

General Pump

MFG MODEL NO

90361200

MAX TEMPERATURE

250°F

MATERIAL

Buna-N 70 Duro

DON'T SEE IT? We can get it! Not sure if this product is right for you, or if there are alternatives? Speak to our sales department:

Call: 1 (800) 676-0607 Email: orders@barens.com

Reliable OEM O-Ring for General Pump T49 & T50 Packing Assemblies

The General Pump 90361200 O-ring is an OEM rubber seal designed for packing assemblies in T49 and T50 series high-pressure plunger pumps. This small but essential item maintains a leak-free seal at the packing retainer, protecting pump performance and extending service life across demanding pressure washing and industrial cleaning applications. The General Pump 90361200 O-Ring measures 1.239" x .07"-an inner diameter and cross-section width engineered specifically to meet General Pump's exact specifications.

What Makes the 90361200 O-Ring Different

Generic o rings may look similar on paper, but pump-specific OEM parts are built to perform under conditions that off-the-shelf seals cannot reliably handle.

  • Exact Geometry for T49 & T50 Pumps – The 1.239" inner diameter × 0.07" cross-section width matches General Pump's packing assembly groove dimensions precisely. Even a slight diameter mismatch can cause under-compression (leading to leaks) or over-compression (accelerating fatigue). The 90361200 eliminates that risk.

  • Rubber Compound Selected for High-Pressure Pumping – The 90361200 O-ring has a hardness rating of 70 durometer in Buna-N (nitrile rubber). Buna-N rubber has good resistance to water and many oils, as well as common detergents and cleaning agents encountered in pressure washing and industrial cleaning environments. This compound maintains its elasticity through repeated pressure cycles and moderate heat exposure.

  • Engineered as Part of a System – This ring was designed to work with the complete T49/T50 packing stack-head rings, high- and low-pressure packing rings, intermediate rings, and metal retainer components. That system-level engineering delivers consistent compression and sealing over thousands of operating hours.

Product Details: General Pump 90361200 O-Ring

  • Material / Compound: Buna-N (nitrile rubber), 70 durometer shore hardness. Resistant to water, many oils, and standard cleaning chemicals used with T-series pumps.

  • Dimensions / Specs: 1.239" inner diameter × 0.070" cross-section width (approximately 31.47 mm × 1.78 mm). Precision-molded round cross-section to OEM tolerances.

  • Compatibility: Used in General Pump packing assemblies on T49 and T50 series solid shaft pumps. The O-Ring is used in General Pump packing assemblies across several model numbers within those series, including T721, T731, T9721, T9731, and others sharing the same 20 mm bore packing geometry.

  • Manufacturer Information: OEM General Pump / Interpump, manufacturer part number 90361200. The General Pump 90361200 O-ring is a vital component for pump maintenance.

  • What's Included: One (1) General Pump 90361200 O-ring. This product is a single seal, not a kit or multi-pack. Packing rings, retainer, and head ring are sold separately unless a complete packing kit is specified.

Frequently Asked Questions

How do I confirm that my pump uses the 90361200 O-ring? Check your General Pump T49 or T50 series manual or exploded parts diagram. Look for the packing retainer callout-if it shows part number 90361200, this is the correct seal. Also confirm your pump's packing bore size is approximately 20 mm, which is standard for these series.

Is the 90361200 O-ring difficult to install? No. Installation is easy and straightforward when the pump head is opened for packing service. Remove the old ring, clean the groove of any debris or buildup, lightly lubricate the new O-ring with water-compatible grease, and seat it flat without twisting or pinching. Reinstall the retainer and tighten to specification.

How often should I replace this O-ring? Replace it whenever performing a packing rebuild. The 90361200 O-ring should be replaced if it shows cracks or deformation, as well as swelling, hardening, or any signs of leaking at the packing area. Under heavy use with hot water or detergents, inspect more frequently.

Does this O-ring fit other General Pump models? The 90361200 is engineered for T49 and T50 series packing assemblies and may also appear in certain TS-Series, CW-Series, and EZ44 series models that share the same packing diameter and retainer geometry. Always verify against your pump's parts list before substituting to avoid a costly error.

Ready to Maintain Your General Pump the Right Way?

The General Pump 90361200 O-ring is a small, inexpensive component that plays an outsized role in keeping T49 and T50 pumps leak-free and running at full efficiency. Rather than waiting for pressure loss or visible dripping, replace this ring proactively during every scheduled packing service-it takes seconds and can save hours of unplanned downtime.